Preen's ADG+ series is an upgraded high power DC power supply, featuring low ripple, high accuracy and fast response. It can simulate various characteristic of solar array with the optional I-V curve function. The Output power is up to 300kW per unit with the patented modularized design and easy mater-slave parallel operation, With the output voltage up to 2000V, making it the ideal choice for applications like EV motor, DC/DC converters, ESS and inverters.
30kW-300kW High Output Power
30kW/50kW
75kW/100kW/300kW
≦0.05% Low Ripple
≦6~10ms Fast Transient Response
2000V Max. Output Voltage (Single Unit)
IV Curve Solar Array Simulation
>90% High Efficiency
ADG+series employs 7” touch screen and rotary knob to provide intuitive and easy-to-use control and display. The built-in programming function has been upgraded, so not only can complex sequences be set from the PC, but also from the touch screen. Emergency stop button is equipped for quick shut down, thus enhancing the product safety. Users can quickly access output settings and measurements, including voltage, current and power.
ADG+ The output power of the ADG+ series is up to 100kW per unit, which can be expanded to 500kW through simple master-slave operation (max. 5 units). User can simply operate the master unit, the slave unit will receive and reply the data accordingly and equally share the load current. ADG+ series is one of the few high-power DC power supply with parallel feature on the market. The availability for single-unit and parallel operation provides greater flexibility for application.
In the factory or laboratory, there is often a certain distance in the configuration of power and load. The Remote Sensing of ADG+ series is able to compensate the voltage drop caused by the cable length, so the user can avoid the inconvenience of adjusting the voltage.
ADG+ high power programmable DC power supply options solar array simulation function, which can be programmed from the front panel without a need for a controller. Using built-in SAS mode, only four input parameter are needed to establish an I-V curve, which simulates solar panels under different irradiation and temperature. Using built-in EN50530 mode, the I-V curve is established according to the solar cell material (C-SI or thin film), and the user can program the output according to the irradiation and temperature; in addition, the user can also define I-V curves based on different material characteristic to simulate various solar cell materials.
SAS Testing Mode
Using SAS mode, user can set Voc, Isc, Vmpp and Impp according to the spec of PV inverter, then the DSP control system performs P-V and I-V curve calculation accordingly. The dynamic irradiation adjustment is also available during output.
EN50530 Testing Mode
Mainly used for grid-tie inverters, the EN50530 Testing Mode features solar cell model of C-SI/thin-film and the feature of dynamic irradiations/temperature adjustment, user can verify the performance of the inverters: static & dynamic MPPT tracking efficiency, conversion efficiency and overall efficiency.
ADG+ series options I-V curve remote control software with parameter setting and output waveform display to verify Dynamic & Static MPPT Efficiency of SAS mode and EN50530 test regulations.
ADG+ series offers complimentary remote control software, Preen Program. This graphical user interface provides easy settings and user-friendly configurations for users to fully control the unit. The Preen Program includes GENERAL mode or PROGRAMMABLE mode with STEP and RAMP features available. The preview waveform and report functions also greatly enhance convenience for on review parameters and results before or after testing.
Specifications
Output Power 30kW/40kW/50kW/75kW/100kW/300kW
DC Output Voltage 0~40V 0~2000V
DC Output Current 0~18A 0~2500A
Output Ripple ≦ 0.1%
Response Time ≦ 6~10mS
Efficiency ≧ 90% at Max. Power
Input Power Factor ≧ 0.9 at Max. Power
Interface RS485
RS232
USB
Analog Control
Ethernet
GPIB (Optional)
Model Number Description